VTM48EH015M050A00【PDF 13/16 页】HALF-CHIP VTM CURRENT MULTIPLIER

您好，
买卖IC网欢迎您。
请登录
免费注册

9页 10页 11页 12页 [13页]14页 15页 16页

VTM 48 EH 015 x 050A00

12.0 INPUT AND OUTPUT FILTER DESIGN

A major advantage of a SAC? system versus a conventional

PWM converter is that the former does not require large

functional filters. The resonant LC tank, operated at extreme

high frequency, is amplitude modulated as a function of input

voltage and output current and efficiently transfers charge

through the isolation transformer. A small amount of

capacitance embedded in the input and output stages of the

module is sufficient for full functionality and is key to achieving

high power density.

This paradigm shift requires system design to carefully evaluate

external filters in order to:

1.Guarantee low source impedance.

To take full advantage of the VTM? module dynamic

response, the impedance presented to its input terminals

must be low from DC to approximately 5 MHz. Input

capacitance may be added to improve transient

performance or compensate for high source impedance.

2.Further reduce input and /or output voltage ripple without

sacrificing dynamic response.

Given the wide bandwidth of the VTM module, the source

response is generally the limiting factor in the overall

system response. Anomalies in the response of the source

will appear at the output of the module multiplied by its

K factor.

3.Protect the module from overvoltage transients imposed

by the system that would exceed maximum ratings and

cause failures.

The VI Chip ? module input/output voltage ranges must

not be exceeded. An internal overvoltage lockout function

prevents operation outside of the normal operating input

range. Even during this condition, the powertrain is

exposed to the applied voltage and power MOSFETs must

withstand it.

13.0 CAPACITIVE FILTERING CONSIDERATIONS

FOR A SINE AMPLITUDE CONVERTER

It is important to consider the impact of adding input and

output capacitance to a Sine Amplitude Converter? on the

system as a whole. Both the capacitance value, and the

effective impedance of the capacitor must be considered.

A Sine Amplitude Converter has a DC R OUT value which has

already been discussed in section 11. The AC R OUT of the SAC

contains several terms:

? Resonant tank impedance

? Input lead inductance and internal capacitance

? Output lead inductance and internal capacitance

The values of these terms are shown in the behavioral model in

section 11. It is important to note on which side of the

transformer these impedances appear and how they reflect

across the transformer given the K factor.

The overall AC impedance varies from model to model but for

most models it is dominated by DC R OUT value from DC to

beyond 500 KHz. The behavioral model in section 11 should be

used to approximate the AC impedance of the specific model.

Any capacitors placed at the output of the VTM module reflect

back to the input of the module by the square of the K factor

(Eq. 9) with the impedance of the module appearing in series.

It is very important to keep this in mind when using a PRM?

regulator to power the VTM?. Most PRM regulators have a

limit on the maximum amount of capacitance that can be

applied to the output. This capacitance includes both the

regulator output capacitance and the current multiplier output

capacitance reflected back to the input. In PRM regulator remote

sense applications, it is important to consider the reflected value

of VTM current multiplier output capacitance when designing

and compensating the PRM regulator control loop.

Capacitance placed at the input of the VTM module appear to

the load reflected by the K factor, with the impedance of the

VTM module in series. In step-down VTM ratios, the effective

capacitance is increased by the K factor. The effective ESR of

the capacitor is decreased by the square of the K factor, but

the impedance of the VTM module appears in series. Still, in

most step-down VTM modules an electrolytic capacitor placed

at the input of the module will have a lower effective

impedance compared to an electrolytic capacitor placed at the

output. This is important to consider when placing capacitors

at the output of the current multiplier. Even though the

capacitor may be placed at the output, the majority of the AC

current will be sourced from the lower impedance, which in

most cases will be the VTM current multiplier. This should be

studied carefully in any system design using a VTM current

multiplier. In most cases, it should be clear that electrolytic

output capacitors are not necessary to design a stable, well-

bypassed system.

Rev. 2.3

VI CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200

6/2012

Page 13 of 16

v i c o r p o w e r. c o m

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

VTM48EH020M040A00 HALF-CHIP VTM CURRENT MULTIPLIER

VTM48EH040M025A00 HALF-CHIP VTM CURRENT MULTIPLIER

VTM48EH120M010A00 HALF-CHIP VTM CURRENT MULTIPLIER

VTM48ET020M080A00 VTM CURRENT MULTIPLIER 2V 80A

VTM48ET030M070A00 VTM CURRENT MULTIPLIER 3V 70A

VTM48ET040M050A00 VTM CURRENT MULTIPLIER 4V 50A

VTM48ET120M025A00 VTM CURRENT MULTIPLIER 12V 25A

VTM48FH060M020A00 HALF-CHIP VTM CURRENT MULTIPLIER

相关代理商/技术参数

VTM48EH015T050A00 功能描述:CONVERT DC/DC VTM 1.32V 50A SMD RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM48EH020_040A00 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTMa?￠Current Multiplier

VTM48EH020040A00 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTMa?￠Current Multiplier

VTM48EH020M040A00 功能描述:HALF-CHIP VTM CURRENT MULTIPLIER RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM48EH020T040A00 功能描述:CONVERT DC/DC VTM 2V 40A SMD RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）

VTM48EH020X040A00 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:Current Multiplier

VTM48EH040_025A00 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTMa?￠Current Multiplier

VTM48EH040M025A00 功能描述:HALF-CHIP VTM CURRENT MULTIPLIER RoHS:是类别:电源 - 板载 >> DC DC 转换器（分解式）系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V）应用:商用特点:具有远程开/关功能和 UVLO 安装类型:通孔封装/外壳:模块尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm）包装:托盘工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）